Home > Catalog

To order this product you must be logged into your distributor account. Not yet a M+A distributor, but interested in becoming one? Fill out this form.

Order Product

Scepter Wet Mops

Stock Product Number MOP_ASTS
Scepter synthetic blend mops are designed to pick up and hold more water than traditional blend mops.  Manufactured with a high concentration of antimicrobial fiber to provide bacterial resistance and superior longevity in a variety ofapplications, the Scepter wet mop dries in half the time of cotton blend mops.
  • Antimicrobial fibers in yarn provide bacterial resistance and superior longevity
  • 4-ply yarn reduces drying time by 50%
  • Septer mops are made with 9" reinforced polyester headbands and double tailbands.
  • Date coded
  • Commercially launderable

Sizes M, L, and XL are stocked in blue and green for quick shipping

The following sizes and colors are stocked in blue and green:
Medium (9" headband)
Large (9" headband)
X-Large (9" headband)

Other sizes are available, but those items are not stocked and require additional lead time.

Follow the Scepter Wet Mop wash instructions carefully for maximum mop head life.

  1. Flush, High, 140°F (50°C) for 2 minutes.
  2. Flush, High, 140°F (60°C) for 2 minutes.
  3. Break/Suds, Low, 140°F (60°C) for 10 minutes
    8oz. built (non solvent) detergent 100 lbs. -4g/kg ph 8.5 - 11.5 maximum
  4. Rinse, High, 140°F (60°C) for 3 minutes
  5. Rinse, High, 120°F (50°C) for 2 minutes.
  6. Rinse/Extract, Low, 80°F (27°C) for 2 minutes
    Active alkalinity no greater than 50 ppm higher than tap water

Additional Processing Information:

  • Centrifugal Extraction: Bring to full speed (300-450 rpm) for 4 minutes and release.
  • Hydraulic Extraction: NOT RECOMMENDED
  • Drying: Tumble at 120° F - 160° F, 49°C - 71° C.Drying:Drying times will vary depending on your geographical location, equipment and the environment and load size. Start by tumbling these mops for 8 minutes at 160°F incoming temperature, 120°F exhaust (If available on your equipment, reverse the dryer drum during the drying cycle. It reduces the drying time and will not create heat pockets in the mop/yarns prolonging their service life). When programming auto dryer settings, monitor temperature for the first 3-6 loads, stop temperature when 140°F is reached, then begin cool down after set point has ran for 3-5 minutes. Cool to 90 - 100°F before unloading.
  • MOPS SHOULD NOT BE FULLY DRY; moisture content should be approximately 10%, unless they are being poly wrapped directly from dryer.
  • Handling/Processing: New mops should be processed separately during their initial wash and the cycles can be overloaded 25 - 30% by weight.  The break operation can be reduced by 3/4 from recommended laundering formula, and maximum water temperature (140°F - 60°C) used.  The final rinse water should be titrated to determine the amount of active alkali.  If higher than 50ppm over tap, an additional rinse will be necessary. To insure the total removal of excess alkali, souring may be desired.  This should be done according to the recommendations of the supplier of the souring chemical.

Notes:

  • All of the processing temperatures are very critical. High washing and drying temperatures can severely damage the fibers.
  • Because Scepter Wet Mops contain a high concentration of synthetic yarn, they will not need to be dried as long as standard cotton blend wet mops.
  • Bleach is not recommended in the wash cycle.
  • Do not over-dry the wet mops.

If you require additional information or require further assistance, please call Golden Star customer service department at 1-800-821-2792 or 1-816-842-0233 or email [email protected]